hello friends! new(ish)!

Home Server/Setting up your Storage

From InstallGentoo Wiki v2
Revision as of 07:50, 23 December 2020 by >DataHoarderAnon (Added ARC. Will expand on later)
Jump to navigation Jump to search

Setting up your RAID Solution

Note: Before Reading, if you do not have a grasp on basic RAID concepts you should read up on that first. There is terminology in this article you will not understand without first understanding RAID.

mdadm

ZFS

Note: There are a lot of misconceptions about ZFS and ECC Ram. ECC Ram is NOT required for ZFS to operate. ZFS was made to protect data against degradation however, and not using ECC Ram to protect against memory errors (and thus data degradation) defeats the purpose of ZFS.

Basic Concepts

Adaptive Replacement Cache (ARC)

Physical Disks are grouped into Virtual devices (Vdevs). Vdevs are grouped into Zpools. Datasets reside in Zpools.

The actual file system portion of ZFS is a dataset which sits on top of the ZPool. This is where you store all of your data. There are also Zvols which are the equivalent of block devices (or LVM LVs). You can format these with other file systems like XFS, or use them as block storage, but for the most part we will be using just the standard ZFS file system. There are also Snapshots and Clones which we will talk about later.

Zpools stripe data across all included vdevs.

There are 7 types of vdevs.

  1. Disk: A single storage device. Adding multiple drives to the same pool without RAIDZ or Mirror is effectively Raid 0.
  2. Mirror: Same as a RAID 1 Mirror. Adding multiple mirrored vdevs is effectively Raid 10.
  3. RAIDZ: Parity based RAID similar to RAID 5. RAIDZ1, RAIDZ2, RAIDZ3 with Single, double, and triple parity respectively.
  4. Hot Spare: A hot spare, or standby drive that will replace a failed disk until it is replaced with a new one.
  5. File: A pre-allocated file.
  6. Cache: A cache device (typically SSD) for L2ARC. It's generally not recommend to use this unless you absolutely need it.
  7. Log: Dedicated ZFS Intent Log (ZIL) device, also called a SLOG (Separate intent LOG SSD). Usually these are high performance, durable SLC or MLC SSDs


Tip: When setting up your drives in ZFS, instead of using the raw disks, make fixed size partitions on each, a little smaller than your drive's full capacity and use that instead. Not all disks have exactly the same sector count. Later down the line if you buy a new drive to replace a failed disk that's a different model or manufacturer, even if it's the correct capacity it may have less sectors and ZFS will not let you use it.

Snapshots and Clones

Should I use ZFS?

ZFS has a lot of really great features that make a a superb file system. It has file system level checksums for data integrity, file self healing which can correct silent disk errors, incremental snapshots and rollback, file deduplication, encryption, and more.

There are however, some downsides to ZFS. Notably inflexibility and the upfront cost. ZFS RAIDZ vdevs CANNOT BE EXPANDED after being created. Parity cannot be added either (you cannot change a RAIDZ1 to a RAIDZ2 later on). You cannot use differently sized disks or disks with data already on them (even disks formatted as ZFS). In other words, you need to buy ALL of the drives you plan on using in your RAIDZ array at the same time, because unlike other software RAID (or even hardware RAID), you won't be able to change it later. This inherently makes ZFS costly to use and thus unfriendly to more budget oriented server builds. Growing your storage is pricy too, as best practice is to add either add identical Vdevs to your existing Zpools, or create an entirely new Zpool. This means at a minimum you need to add two drives at a time to maintain proper redundancy (if using mirrored pairs). You can "Vertically" expand your Zpool by replacing each disk in a RaidZ array with a larger disk, but this requires resilvering the array each time and for larger arrays can take Weeks or even Months so it is not recommended. Now also add in the fact that running ZFS also requires a hefty amount of RAM, preferably ECC ram (which is expensive in and of itself), requires server hardware to utilize to it's fullest, and that some of the fancy features like dedup also require a good processor too..

The price tag starts to add up really quickly.

So when asking yourself "Should I use ZFS?" you really should be asking "Do I really need ZFS?" (Do I want long term data integrity and all those other fancy features?) and "Can I afford ZFS?". If the answer to both of those questions is "Yes", then you can and should use ZFS, otherwise use something else like Snapraid or mdadm.


Not Recommended:

  • Running ZFS on old hardware.
  • Running ZFS on ancient hardware.
  • Running ZFS on consoomer motherboards.
  • Run ZFS without ECC Ram. If you can afford ZFS you can afford to get ECC Ram. No excuses.
  • Run ZFS on underqualified hardware (shitty little NAS boxes, SBCs, etc).
  • Use "Mutt" pools (Zpools with differently sized vdevs).
  • Growing your Zpool by replacing disks. Backup your data elsewhere, create a new pool, and transfer the data to the new pool. Much faster. (You could theoretically use a USB drive dock provided your array is 5 disks or less).


DO NOT

  • Run ZFS on top of Hardware RAID.
  • Run ZFS on top of other soft RAID.
  • Run ZFS in a VM without taking the proper precautions.
  • Run ZFS with SMR drives.


Btrfs

Snapraid

Hardware RAID

Warning: Using hardware RAID and software RAID at the same time is NOT recommended. If you wish to pool multiple hardware RAID arrays together into a logical volume use LVM.

If you bought an old used server with a RAID controller already installed, or perhaps you don't feel like messing with software RAID solutions, you have the option of using hardware RAID rather than software RAID.


Choosing a file system

XFS

ext4

NTFS

If you are using snapraid as your raid solution, using NTFS formatted drives is perfectly fine. With Snapraid you are usually pulling out random drives you have lying around, which are most likely to be NTFS formatted. Otherwise, we do not recommend using NTFS unless you are running a Windows server for some reason. It does not have the same level of support on Linux and UNIX based systems as ext4 and XFS.

unRAID does not support NTFS. If you are using unRAID you will need to use ext4 or XFS.


Distributed Filesystems

CEPH

seaweedfs

lizardfs

moosefs

External Links

See also